Skatewheel Conveyor

WHEELS: 1-15/16" dia. pre lubricated ball bearing wheel with hardened raceway. Aluminum wheel capacity is 25 lbs. per wheel; zinc-plated wheel capacity is 50 lbs. per wheel.
AXLES: 1/4" dia. galvanized steel bolt-type axle and lock nut.
FRAMES: Formed heat-treated aluminum channel 2-1/2" x 1" x 1/8"; formed galvanized steel channel 2-1/2" x 1" x 12 ga. 

COUPLINGS: Hook and rod; hooks on one end and rod ("stud") other end. 

FRAME CAPACITY: Aluminum 160 lbs. max. distributed live load per 10' section or 750 lbs. per 5' section; galvanized steel 350 lbs. max. distributed live load per 10' section, or 1300 lbs. per 5' section.

Medium Duty Gravity Conveyor

ROLLERS: 1-3/8" dia. x 18 ga. tubing available in heat treated alum. (model 138A) or galvanized steel (model 138G); both with smooth swaged ends. Roller capacity is 35 lbs. for 138A; 50 lbs. for 138G.
AXLES: 1/4" dia. galvanized steel shaft, spring loaded.
FRAMES: Formed heat treated aluminum channel 2-1/2" x 1" x 1/8"; formed galvanized steel channel 2-1/2" x 1" x 12 ga.

COUPLINGS: Hook and rod; hooks on one end and rod ("stud") other end. 
BEARINGS: Integral plain ball bearings, zinc plated, oiled.
FRAME CAPACITY: Aluminum 160 lbs. max. distributed live load per 10' section or 750 lbs. per 5' section; galvanized steel 350 lbs. max. distributed live load per 10' section, or 1300 lbs. per 5' section.

Gravity Roller Conveyor

ROLLERS: 1.9 " x 16 ga. galvanized steel tubing, model 196G, with smooth swaged ends.
FRAMES: Formed steel painted channel  3-1/2 " x 1-1/2 " x 10 ga. set high; 4-1/2 " x 1-1/2 " x 10 ga. set low.
BEARINGS: Integral plain ball bearings, zinc plated, grease packed.
FRAME CAPACITY: 250 lbs. per roller,  or 1300 lbs. maximum distributed live load per 10' section with supports at 10' centers; 3200 lbs. at 5' centers.

COUPLINGS: Butt type.
AXLES: 7/16 " hex shaft, spring loaded.

Ball Transfer

BALL ASSEMBLIES: 1" dia. steel ball x  1-13/16" overall housing diameter. Mounting bolt is 1/4"-20.
BALL CAPACITY: 50 lbs. per ball with max. unit load not to exceed the capacity of 4 balls (200#).
FRAMES: 3-1/2" x 1-1/2" x 10 ga. steel with balls in set high position (1/4" above side frames) only.

FRAME CAPACITY: 1300 lbs. maximum distributed live load per 10' section with supports at 10' centers; 3200 lbs. at 5' centers.
PLATES: Balls are attached in square  pattern to 10 ga. formed plates up to 39" BF. Above 39", plates are 7 ga.

Line Shaft Conveyor

TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved.

DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.

DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D").

CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC.

BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached w/ splice plates and floor supports.

BEARINGS: Precision, lubricated, ball bearing units with composite housings.

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.

Line Shaft Zero Pressure, Zone Accumulation Conveyor

TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved.

DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft.
COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D").

CENTER DRIVE: Located approximately 16-1/2" from end of bed section on 4" RC; 18" on 3" and 6" RC.

BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.

ACCUMULATION: Zone singulation operation; 2'-0" zone length, photo eye controlled.

BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports.

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.

TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved, 3" centers.

DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.

DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft. NOTE: Spools in spur section only are keyed to provide positive drive (designed not to slip on drive shaft).

COUPLINGS: Couplings located both ends or one end only.

BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Short side of spur is always 12" overall length.

Line Shaft Conveyor Curve

TREAD ROLLERS: 1.9" dia. x 16 ga. steel, model 196S grooved.

DRIVE BELT: 3/16" dia., polyurethane belts. Nominal 15 lbs. per roller drive.
DRIVE SHAFT: 1" dia. C1018 cold rolled steel shaft, located on inside radius.

COUPLINGS: Couplings located both ends (type "A"), one end only (type "B" or "C") or none (type "D").

BEARINGS: Precision, lubricated, ball bearing units with composite housings.

CENTER DRIVE: Reversible drive; located approximately 18" from end of bed section for 3" and 6" RC; 16-1/2" for 4" RC.

BED: 7" x 1-1/2" x 12 ga. formed steel channel frame. Bed sections attached with splice plates and floor supports.

ROLLER CHAIN: Drive shaft is driven by No. 50 chain. Chain take-up provided on motor base.

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.  Options Available

Chain Driven Heavy Duty Live Roller Conveyor

TREAD ROLLERS: 2-9/16" dia. x 7 ga. steel rollers, model 297S with sprockets.
CHAIN DRIVE: Roller to roller with No. 60 roller chain.

ROLLER CENTERS: 4-1/2", 6", 9" or 12".
CENTER DRIVE: Reversible drive either side mounted or underside mounted (specify). Main drive roller is supported by precision, heavy duty, lubricated, ball bearing units.
BED: 4" at 5.4 lbs. and 6" at 8.2 lbs. structural steel channel frame. Bed sections attached with couplings and floor supports.

SPEED: 35 FPM, constant.

BEARINGS: Removable type, heavy duty ball bearings, zinc-plated, grease packed, labyrinth sealed. Roller bearings provide roller capacity of 540 lbs. per roller (maximum).

CHAIN GUARD: The chain drive is completely enclosed along the entire length of the conveyor.

BED LENGTHS (4-1/2" or 9" RC): Intermediate bed section lengths 3'-0",  3'-9", 4'-6", 5'-3", 6'-0", 6'-9", 7'-6", 8'-3", 9'-0" and 9'-9" increments. Minimum overall conveyor length with drive 5'-3". Maximum overall conveyor length: 58'-6" with 4-1/2" RC; 78'-0" with 9" RC.

BED LENGTHS (6" or 12" RC): Intermediate bed section lengths are available in 1'-0" increments. Minimum overall conveyor length with drive 5'-0". Maximum overall conveyor length 80'-0".

MOTOR DRIVE: 3/4 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

Chain Drive, Live Roller, Zone Accumulation Conveyor

TREAD ROLLERS: 1.9" dia. x 12 ga., model 192S.
CHAIN DRIVE: Roller-to-roller No. 40 roller chain. Zone-to-zone No. 60 roller chain.
CHAIN GUARD: All chains are completely enclosed along the entire length of conveyor.

CENTER DRIVE: Drive either side mounted or underside mounted (specify). Drive shafts are supported by precision, heavy duty, lubricated, ball bearing units.

ROLLER CENTERS: 4" or 6" RC ONLY.
SPEED: 35 FPM, constant.

ACCUMULATION ZONE: 5'-0" zone lengths, zone singulation operation, photo electric sensor controlled zones with separate drives on each zone.

BED: 6-1/2" x 1-1/2" x 10 ga. and 4-1/2" x 1-1/2" x 10 ga. formed steel channel frame. Bed sections are bolted together with butt couplings and floor supports.

FLOOR SUPPORTS: Optional

BEARINGS: Removable type, heavy duty ball bearings, zinc-plated, grease packed, labyrinth seal.

FRL: Unit is provided with filter, regulator  and lubricator with 3/8" ports for 60 PSI operational pressure.

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

CAPACITY: 300 lbs./ft. up to a maximum of 1200 lb. pallet load.

Chain Driven Heavy Duty Live Roller Curve Conveyor

TREAD ROLLERS: 2-9/16" dia. x 7 ga. steel, model 297S with sprockets.
CHAIN DRIVE: Roller to roller with No. 60 circular roller chain.

END DRIVE: Reversible drive either side mounted or underside mounted (specify). Main drive roller is supported by precision, heavy duty, lubricated, ball bearing units.

CHAIN GUARD: The chain drive is completely enclosed along the entire length of the conveyor.

ROLLER CENTERS: 6" RC measured at outside radius of curve.

BED: 4" at 5.4 lbs. and 6" at 8.2 lbs. structural steel channel frame.

BEARINGS: Removable type, heavy duty,  ball bearings, zinc plated, grease packed, labyrinth sealed.
MOTOR DRIVE: 3/4 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

SPEED: 35 FPM, constant.

FLOOR SUPPORTS: SH-4 with underneath mounted drive adjustable 18" to 21" TOR. SH-1 with side mounted drive adjustable 10-1/2" to 12" TOR. Supports should be lagged to floor.

DRIVE LOCATION: Drive located on outside of curve. Specify right hand drive or left hand drive (drive hand determined with  reference point located at outside of curve).

Live Roller Cam Adjusted Medium Duty Conveyor

TREAD ROLLERS: 1-.9" dia. x 16 ga. steel rollers, model 196S.
PRESSURE ROLLERS: 1.9" dia. x 16 ga. steel, model 196S, cam adjustable.
BELTING: 6" wide black PVC-120 COS.
CENTER DRIVE: Reversible drive with 24" integral belt take-up. For units under  8'-0" overall length, drive components must be stacked. Consult factory for minimum unit elevation.

SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30'.
DRIVE PULLEY: 4" dia. with 1-3/16" dia. shaft or 8" dia. with 1-7/16" dia. shaft; both crowned and fully lagged.
END PULLEY: 4" dia., crowned, with 1-3/16" dia. shaft.

RETURN ROLLERS: 1.9" dia. x 16 ga. steel, model 196S

BED: 6" x 1-1/2" x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7'-0" elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.

BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.

ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. Options Available

Live Roller Conveyor Curve Spur   

TREAD ROLLERS: 1.9" dia. to 1-3/8" dia. x 16 ga. tapered rollers, model 138T; 1-3/8" dia. x 18 ga., model 138G w/ 5/16" hex, galvanized straight tangent rollers.
ROLLER CENTERS: 1-9/16" measured at inside radius of unit.
PRESSURE SHEAVES: Provides drive belt pressure to upper tread rollers.
BELTING: "B" section V-belt.

TAKE-UP: Screw type adjustable sheave with flat idler sheaves to maintain belt tension.
TANGENTS: 12" both ends on 60/30 degree unit; 18" both ends on 45/45 degree unit.

BED: 6" x 1-1/2" x 12 ga. formed steel channel frame.

BEARINGS: End shafts are supported by precision, heavy duty, lubricated, ball bearing units with cast iron housings.

ROLLER CHAIN:Drive shaft is driven by No. 50 chain.

FLOOR SUPPORTS: Optional

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor, located under tangent straight section bed

DRIVE LOCATION: Drive located on outside of curve. Specify left hand tangent length, right hand tangent length and drive location ("left hand drive" or "right hand drive"). NOTE: Drive hand determined with reference point located at outside of curve. For models slave driven (less drive), specify drive shaft location.

Live Roller Conveyor Curve

TREAD ROLLERS: 2-1/2" dia. to 1-11/16" dia. x 14 ga. steel tapered rollers, model 254T; 1.9" dia. x 16 ga. steel straight tangent rollers, model 196S.
PRESSURE SHEAVES: Provides drive belt pressure to upper tread rollers.
BELTING: "B" section V-belt.
TAKE-UP: Screw type adjustable sheave with flat idler sheaves to maintain belt tension.
TANGENTS: 1'-0" both ends on 90 degree;  1'-6" both ends on 45 degree; 1'-0" both ends on 180 degree. Tangent roller centers provided on 3" RC.
SPEED: 60 FPM, constant

BED: 7" x 1-1/2" x 12 ga. formed steel channel frame.
BEARINGS: End shafts are supported by precision, heavy duty, lubricated, ball bearing units with cast iron housings.
ROLLER CHAIN:Drive shaft is driven by No. 50 chain.

DRIVE LOCATION: Drive located on outside of curve. Specify left hand tangent length, right hand tangent length and drive location ("left hand drive" or "right hand drive"). NOTE: Drive hand determined with reference point located at outside of curve. For models slave driven (less drive), specify drive shaft location.
CAPACITY: 500 lb. total distributed live load.

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor, located at infeed end of curve below bed on 45 degree and 90 degree curves; 3/4 HP supplied on all 180 degree curves.

Roach has several styles of Belt Conveyors available. The main two types of belt conveyors are slider beds and roller beds.

The trough bed belt conveyor has an integrated guard rail which is ideal for trash conveyor, handling chips, slugs, scrap wood, paper waste, boxes, packages, and cartons.
The standard slider bed belt conveyor is one of the most economical options for transporting conveyors.
The box style slider bed is another option which provides a smooth surface along the side of the conveyor. The box style slider bed is ideal for workers stationed beside the conveyor.

The roller bed is well suited for transporting heavier unit loads with less horsepower than required by slider beds

Variety of widths available

Belt Conveyor Incline/Decline

BELTING: Black PVC rough-top.
DRIVE PULLEY: 8" dia. with 1-7/16" dia. shaft, both crowned and fully lagged.

CARRIER ROLLERS: 1.9" dia. x 16 ga. steel rollers, model 196S.
TAIL PULLEY: 4" dia., crowned, with 1-3/16" dia. shaft.
CENTER DRIVE: Reversible drive with 24" belt take-up.

NOSE-OVER: Provides smooth transition from incline to horizontal position.  Single nose-over adjust 0-20 degrees; double nose-over adjust 0-35 degrees.

BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.
RETURN ROLLERS: 1.9" dia. x 16 ga. steel, model 196S, adjustable.

BELT SPEED: 60 FPM, constant.

BED: 7" x 12 ga. channel frame.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.

Roach has a complete line of plastic belt conveyors featuring the Intralox belt. The plastic belt conveyor is a slider bed belt conveyor with different plastic belt configurations. Belts available include friction top, roller top, flush grid, flat top, raised rib, and flat top with flights.

Parts Conveyor With Feeder

BELTING: 3-ply black nitrile belt or 1/2" x 1" flat wire mesh belt with 1-1/2" high galvanized cleats on 12" centers.
DRIVE PULLEY: 4" dia., with 1-3/16" dia. shaft, fully lagged with nitrile belt; 4" dia. sprockets supplied with flat wire mesh belt.
TAIL PULLEY: 4" dia. with 1-3/16"
dia. shaft.
TAKE-UP: Screw type unit at tail pulley provides 12" belt take-up.
BED: 8" deep x 12 ga. enclosed box
type construction with 14 ga. steel belt return pan.
BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.

BELT SPEED: 35 FPM, constant.

MINIMUM PARTS SIZE: 1/2" cube for nitrile belt, 1" cube for flat wire mesh belt.
INCLINE: 30, 36 and 45 degree (specify).
PORTABLE SUPPORT: Adjustable floor support with 4" dia. casters and bracing.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.
CAPACITY: 350 lbs. total distributed load.
ROLLER CHAIN: No. 50 chain provided at drive pulley. Chain take-up provided on motor base.

Flat Top Plastic Belt Parts Conveyor With Flights

BELTING: Series 900 flat top gray polypropylene belt with 2" high streamline flights on 11.9" centers, FDA approved belting.
DRIVE SPROCKETS: 4.1" pitch dia. with 1.5" square bore.
TAIL SPROCKETS: 4.1" pitch dia. with 1.5" square bore.
END DRIVE: Allows one-direction (unit) operation.
TAKE-UP: Catenary type, underneath mounted.
BEARINGS: Drive shaft bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.

BELT SPEED: 35 FPM, constant.

BED: 8" deep x 10 ga. enclosed box type construction with UHMW wear strips mounted to 14 ga. steel belt return pan.

INCLINE: 30, 36 and 45 degree (specify).

PORTABLE SUPPORT: Adjustable floor supports with 4" dia. casters & bracing.
ROLLER CHAIN: No. 50 chain provided at drive shaft. Chain take-up provided on motor base.
MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

2-Strand Chain Drag Conveyor

FRAME: 7 ga. formed boxed channel.

CARRIER CHAIN: No. 80 (model CD280) or no. 60 (model CD260) riveted roller chain.

WEAR STRIP: UHMW long lasting wear strip, upper and lower.
CHAIN CENTERS: 18"

CHAIN TAKE-UP: Screw type located at tail end.
END DRIVE: Allows one-direction (unit) operation; add optional center drive for reversible application.
CHAIN SPEED: 35 FPM constant.

BEARINGS: Heavy duty, lubricated, ball bearing unit with cast iron housings.

CAPACITY: Unit load not to exceed 3000 lbs.

FLOOR SUPPORTS: Optional.

MOTOR DRIVE: 1/2 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

Heavy Duty Slat Conveyor

SLAT: 5-3/4" wide formed 7 ga. steel channel.
DRIVE: End side mount drive.
SPEED: 35 FPM, constant (maximum).
TAKE-UP: Screw type.
BED: 19-3/4" deep formed steel channel.
FLOOR SUPPORTS: Supports for elevations of 20" to 26-1/4" will be fixed height supports. Above 26-1/4", standard SH supports will be used.

MOTOR DRIVE: 3/4 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

Chain Transfer 3-Strand 90 Degree Conveyor

FRAME: 7 ga. formed channel.

TRANSFER CHAIN: No. 80 (model CD380) or no. 60 (model CD360) riveted roller chain.

STANDARD LENGTHS: 3', 4', 5' 6', 7' and 8' unit lengths.
CHAIN CENTERS: 18"

CHAIN TAKE-UP: Screw type.
END DRIVE: Allows one-direction (unit) operation; add optional center drive for reversible application.

LIFT: Pivot type.

CHAIN SPEED: 35 FPM constant.

BEARINGS: Heavy duty, lubricated, ball bearing unit with cast iron housings.

CAPACITY: Unit load not to exceed 4000 lbs.

FLOOR SUPPORTS: Integral part of unit.

MOTOR DRIVE: 1/2 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

AIR CONTROLS: Air chambers with single solenoid valve.

CUTOUTS: Required through conveyor.

3-Strand 90 Degree Round Belt Transfer Conveyor

TRANSFER ARM: 10 ga. formed channel.

TRANSFER BELT: 3/8" dia. round polyurethane belt.

LENGTHS: Transfer designed to mount in 796LS line shaft conveyors 15"-39" BF.

BELT CENTERS: 12"

ONE DIRECTION FLOW: Transfers product in one direction.

TAKE-UP: Adjustable sheaves provides take-up of transfer belt.

BEARINGS: Heavy duty, lubricated, ball bearing units with cast iron housings.

BELT SPEED: Driven at 150% of speed as powered section transfer is mounted in.

LIFT: 3/4" positive lift.

MOTOR DRIVE: Optional.

CAPACITY: 100 lbs.

AIR CONTROLS: Air cylinder with single solenoid valve.

Flite Sorter Conveyor

ROLLERS: Densely located to carry various size unit loads/weights.

FRAME: Heavily constructed 12 ga. for long lasting operation.

DIVERT SHOES: Guided by UHMW wear strip for smooth, quiet operation.

RATE: 150 cartons/Minute maximum.

DRIVE: 1 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

SPEED: Varies with desired rate of flow.

FLOOR SUPPORTS: 31"-40" TOR. Supports provided at both ends and each bed joint.

ELECTRICAL CONTROLS: Custom designed for specific application. Consult factory.

PACKAGE SIZE: Minimum length 9"; maximum length 48". Minimum width 1"; maximum width 36".

PACKAGE WEIGHT: Preferred package weight range is 2 to 100 lbs.

High Speed Sorter Conveyor

Indexing Powered Turntable

ROTATION: 2 position, 3 position or 4 position.
SPEED: 35 FPM at outside diameter.
CHAIN DRIVE: No. 80 roller chain.
CHAIN GUARD: The chain drive is completely enclosed.
CASTERS: (8) 4" dia. heavy duty rubber-covered casters support rotation of turntable carrier platform.
DIAMETER: 3'-0", 3'-6", 4'-0", 4'-6", 5'-0", 5'-6", 6'-0", 6'-6", 7'-0", 7'-6" and 8'-0" dia.
CARRIER PLATFORM: 3" structural platform with 1/2" thick steel plate supported by heavy duty casters.

BEARINGS: Heavy duty ball bearing 4-hole flange.

CAPACITY: 4000 lbs. max. product load.
MOTOR DRIVE: 3/4 HP, 230/460/3, 60 cycle, ODP right angle gear motor with brake.
ELEVATION: Minimum 12-1/2" to top of plate with (4) structural leveling supports.
ELECTRICAL CONTROLS: Limit switches supplied as follows: 2 position = 2 limit switches; 3 position = 3 limit switches; 4 position = 4 limit switches.

Pallet Stacker/De-Stacker

The pallet stacker, shown above, is designed and manufactured by Roach to stack 48" wide x 40" long x 6" tall pallets. 

A 2-strand chain drag conveyor, 36" strand centerline is mounted at 17-1/2" elevation which conveys individual pallets into the stacker and stacks of pallets OUT of the stacker.

Vertical Reciprocating Flow Conveyor

CAPACITY: Up to 4000 lbs.
FRAME: Heavy duty tubular construction.
DRIVE: (2) heavy strands of chain to raise and lower carrier platform.
RATE: Varies with unit height.
SPEED: 60 FPM (120 FPM maximum).

LOADING: One or more loading points may be selected at any level.
PLATFORM: Specify conveyor type.
GUARDS: Expanded metal guarding.